• No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, microfilming, recording, or otherwise, without written permission from Axon Instruments, Inc. Phone: +1 (510) 675-6200. • COPYRIGHT The information in this manual is copyrighted and must not be reproduced in any form whatsoever without written permission from Axon Instruments, Inc. VERIFICATION This instrument is extensively tested and thoroughly calibrated before leaving the factory. Nevertheless, researchers should independently verify the basic accuracy of the instrument using suitable test signals. • EN 50082-1: 1998 Safety: EN 61010-1: 2001 I, the undersigned, hereby declare that the equipment specified above conforms to the above Directives and Standards. Authorized Signature and Date: (Signature on file) Digidata 1322A Operator’s Manual, Copyright 2000-2001, Axon Instruments, Inc. • TABLE OF CONTENTS Chapter 1 INTRODUCTION..1 Introduction to the Digidata 1322A..1 Components...2 Minimum Computer Requirements..2 Recommended Computer System.. 2 Notes on the SCSI Adapter Card... 3 Rack Mount Kit...3 Chapter 2 INSTALLATION..5 Instructions... • Chapter 5 SPECIFICATIONS..21 Analog Input...21 Analog Output...22 Digital Inputs...22 Digital Outputs...22 Trigger In... 22 STANDARD WARRANTY and REPAIR SERVICE.23 INDEX...25 Digidata 1322A Operator’s Manual, Copyright 2000-2001, Axon Instruments, Inc. • The Digidata 1322A has higher speed, lower noise and better resolution (greater dynamic range) than the previous Digidata 1200 models. New features also include better instrument telegraph support and line-frequency triggering. The Digidata 1322A is intended for benchtop use, but it is supplied with a simple rack-mount kit. Where can I download the drivers for the Digidata 1200 series of digitizers? 16-bit driver (for DOS, Windows 95, Windows 98 and Windows ME) 32-bit driver. • Parallel port (if using with the parallel port key required by pCLAMP) • 1024 x 768 display system (large or small fonts) • Windows 95, 98, NT 4.0, or Windows 2000 operating system (PC), OR System 9 (Mac) Digidata 1322A Operator’s Manual, Copyright 2000-2001, Axon Instruments, Inc. • Rack Mount Kit The Digidata 1322A is designed to be a desktop unit. However, some users may want to mount the Digidata 1322A in a rack, so a Rack Mount Kit is provided. The Rack Mount Kit includes the following parts. • Tighten the Side Bracket set screws up against the side panels. Secure the entire unit in the rack a. Place the unit (Digidata 1322A) plus the attached rack mount assembly in the rack. Tascam Us 1200 Driver DownloadSecure the Rack Mount Panel to the rack with four rack screws (not included). • If you have a Digidata 1200A or 1200B system that you still wish to use, it is OK to leave the old Digidata board in the computer and to leave DriverLinx installed during the Digidata 1322A installation. Also, pCLAMP 8 users do not need to install the AxoScope CD that comes with the Digidata 1322A. AxoScope is automatically installed with pCLAMP 8 and above. • Install AxoScope or pCLAMP 8 (press the third button). At the end of installation, a prompt asks if you want to reboot. Shut down and turn off the computer to connect the Digidata 1322A (it is not advisable to connect to the SCSI port while the computer is on). Hp Laserjet 1200 Driver DownloadIphone driver download. • We recommend that the Digidata 1322A be calibrated whenever there is a change in the environment, such as moving it to another room or installing it on another computer. The Digidata 1322A is now ready to perform experiments. • The Power-on Holding Levels section is used to set the voltage on both Analog Out channels at the time that the Digidata 1322A is turned on. The initial Digital Out levels can also be set high or low by clicking on the check boxes above the numbers corresponding to each digital output (a check means high, blank means low).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
December 2018
Categories |